Anschutz 8002 - Scope Rail & Wheel
- AdminMASTER
- Site Admin
- Contact:
- Go to Rifle: Feinwerkbau 800
- Country: United-Kingdom
- Where: London
Post
#1 Anschutz 8002 - Scope Rail & Wheel
Credit: Steve (UK)
Signature - https://www.instagram.com/pimpmyairgun/?hl=en
- Jon
- Contact:
- Go to Rifle: JH
- Country: UK
Post
#2 Re: Anschutz 8002 - Scope Rail & Wheel
Funny story that ended well with that rail.
Above rail was made in a panic to replace the stolen one similar looking at the Shooting Show.
Last night Steve PM's me from a pub in Bolton, pub talk other chap says i have a rail like that in car. They go outside and Steve says i know whos made them and know whos they are, hand them over now. Also get my IP67 vernier back and a special rail with built in bubble i didnt want to remake but lost the other stuff.
So a massive thank you to Steve and the lad who brought them up from the show.
Small world.
Above rail was made in a panic to replace the stolen one similar looking at the Shooting Show.
Last night Steve PM's me from a pub in Bolton, pub talk other chap says i have a rail like that in car. They go outside and Steve says i know whos made them and know whos they are, hand them over now. Also get my IP67 vernier back and a special rail with built in bubble i didnt want to remake but lost the other stuff.
So a massive thank you to Steve and the lad who brought them up from the show.
Small world.
If a jobs worth doing, do it right or not at all.
- AdminMASTER
- Site Admin
- Contact:
- Go to Rifle: Feinwerkbau 800
- Country: United-Kingdom
- Where: London
Post
#3 Re: Anschutz 8002 - Scope Rail & Wheel
..this is the AWESOME set up...
Signature - https://www.instagram.com/pimpmyairgun/?hl=en
- Steve
- Go to Rifle: Walther
- Country: Uk
- Where: Bolton
-
Pa
Post
#5 Re: Anschutz 8002 - Scope Rail & Wheel
I know someone who will print an enlarged print of that, pin it up on his bedroom wall and will have wet dreams
- Jon
- Contact:
- Go to Rifle: JH
- Country: UK
Post
#6 Re: Anschutz 8002 - Scope Rail & Wheel
Know who you mean Paul he will have to get up there before his mrs.
Looking good Steve just getting the red one ready for Saturday.
Looking good Steve just getting the red one ready for Saturday.
If a jobs worth doing, do it right or not at all.
- Steve
- Go to Rifle: Walther
- Country: Uk
- Where: Bolton
- Jon
- Contact:
- Go to Rifle: JH
- Country: UK
Post
#8 Re: Anschutz 8002 - Scope Rail & Wheel
It was
Thought I could make it better now its had around 500 through it, found a sweet spot and wanted to set reg pressure there. As is after reg tune-
0.2+0.1mm shim = 79bar
0.2+0.2mm shim + 130bar
0.5mm shim 180bar
So some fun and games, lots of trial and error.
It should have another 500 through it tomorrow
Thought I could make it better now its had around 500 through it, found a sweet spot and wanted to set reg pressure there. As is after reg tune-
0.2+0.1mm shim = 79bar
0.2+0.2mm shim + 130bar
0.5mm shim 180bar
So some fun and games, lots of trial and error.
It should have another 500 through it tomorrow
If a jobs worth doing, do it right or not at all.
- Steve
- Go to Rifle: Walther
- Country: Uk
- Where: Bolton
Post
#9 Re: Anschutz 8002 - Scope Rail & Wheel
Looks like that's going to be a fine balancing act Jon,with so little making such a change.
Who is online
Users browsing this forum: No registered users and 1 guest