credit - Juan (ESP)
15.42mm - tip and end of barrel
16.12mm - center part of barrel
Differential: 0.7mm
Barrel Diameter - ATAMAN M2 FT
- AdminMASTER
- Site Admin
- Contact:
- Go to Rifle: Feinwerkbau 800
- Country: United-Kingdom
- Where: London
Post
#1 Barrel Diameter - ATAMAN M2 FT
- Attachments
-
- ata barrel -1.jpg (51.33 KiB) Viewed 1717 times
-
- ata barrel -2.jpg (85.26 KiB) Viewed 1717 times
Signature - https://www.instagram.com/pimpmyairgun/?hl=en
- AdminMASTER
- Site Admin
- Contact:
- Go to Rifle: Feinwerkbau 800
- Country: United-Kingdom
- Where: London
Post
#2 Re: Barrel Diameter - ATAMAN M2 FT
credit; JUAN (ESP)
Nice one
6.695 Kg = 14.75 lbs.
Nice one
6.695 Kg = 14.75 lbs.
- Attachments
-
- JUAN - ATAMAN M2 FT.JPG (104.09 KiB) Viewed 1714 times
Signature - https://www.instagram.com/pimpmyairgun/?hl=en
- AdminMASTER
- Site Admin
- Contact:
- Go to Rifle: Feinwerkbau 800
- Country: United-Kingdom
- Where: London
Post
#3 Re: Barrel Diameter - ATAMAN M2 FT
...according my friend Juan, the ATAMAN block requires 13.96mm
So anyone wanting a CZ hammer forged barrel, can/should simply order the O/D 15mm ; or if wanting BEEFIER barrel , gunsmith can still cut down the 16 mm O/D
which is what I think I will order (since the carbon sleeve I want should fit nicely at 16mm >
German Carbon tube supplier >> http://pimpmyairgun.com/viewtopic.php?f=123&t=91
CZ Hammer Forge>> http://pimpmyairgun.com/viewtopic.php?f=237&t=1775
So anyone wanting a CZ hammer forged barrel, can/should simply order the O/D 15mm ; or if wanting BEEFIER barrel , gunsmith can still cut down the 16 mm O/D
which is what I think I will order (since the carbon sleeve I want should fit nicely at 16mm >
German Carbon tube supplier >> http://pimpmyairgun.com/viewtopic.php?f=123&t=91
CZ Hammer Forge>> http://pimpmyairgun.com/viewtopic.php?f=237&t=1775
Signature - https://www.instagram.com/pimpmyairgun/?hl=en
- NeilM
- Go to Rifle: Whiscombe
- Country: United Kingdom
- Where: Weston-super-Mare
Post
#4 Re: Barrel Diameter - ATAMAN M2 FT
Is the barrel change a necessary one? Or just for the pleasure of it?
The Tsar I shot / tested was pretty good already and will only get better with shooting. Change the barrel to a hammer forged CZ and you will have to go through the whole shooting in process all over again.
That said, I am pondering a CZ barrel for my ISP.
The Tsar I shot / tested was pretty good already and will only get better with shooting. Change the barrel to a hammer forged CZ and you will have to go through the whole shooting in process all over again.
That said, I am pondering a CZ barrel for my ISP.
- AdminMASTER
- Site Admin
- Contact:
- Go to Rifle: Feinwerkbau 800
- Country: United-Kingdom
- Where: London
Post
#5 Re: Barrel Diameter - ATAMAN M2 FT
Got an email from JUAN (ESP)
- Attachments
-
- image1.JPG (76.43 KiB) Viewed 1589 times
-
- image2.JPG (99.98 KiB) Viewed 1589 times
-
- image3.JPG (97.08 KiB) Viewed 1589 times
-
- image4.JPG (90.45 KiB) Viewed 1589 times
Signature - https://www.instagram.com/pimpmyairgun/?hl=en
Who is online
Users browsing this forum: No registered users and 0 guests